Select [Auto] to automatically detect the hard disk drive. Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Click on a specific item then follow the installation wizard to install it. Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply.
|Date Added:||12 January 2014|
|File Size:||43.32 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
You may also restart by turning the system off and then back on. The lever clicks on the side tab duwl-915gl indicate that it is locked.
ASRock P4DualGL, Socket , Intel Motherboard | eBay
Refer to your OS documentation for more information. This section will guide you to install the SATA hard disks.
For the user password, you may also clear it. Click on a specific item then follow the installation wizard to install it. Operation is subject to the following two conditions: In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages including damages for loss of profits, loss of business, loss of data, interruption of business dual-915tl the likeeven if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product.
Keep the screws for later use. Ring-In Power On Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode. This motherboard supports Dual Channel Memory Technology. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation.
The actual CPU host frequency will show in the following item. OnBoard Dyal-915gl Controller Use this item to enable or disable floppy drive controller.
Ratio Actual Value This is a read-only item, which displays the ratio actual value of this motherboard.
For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.
Asrock P4DUAL-915GL User Manual
Not Installed User Password: This header supports an optional wireless transmitting and receiving infrared module. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. Serial Port Address Use this item to set the address for the onboard serial port or disable it.
If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology. ASRock assumes no responsibility for any errors or omissions that may pp4 in this asroco.
Self-Monitoring, Analysis, and Reporting Technology feature. Install the SATA hard disks into the drive bays of your chassis. The current SATA interface allows up to 1.
ASRock P4Dual-915GL – motherboard – micro ATX – Socket 478 – i915GL
To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short asrokc pins on CLRCMOS1 for 3 seconds. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! See the table below for connection details in accordance with the type of speaker you use.
While CPU overheat is detected, the system will automatically shutdown. Pre-installation Precautions Take note of the following precautions before dual-195gl install motherboard components or change any motherboard settings.
Then connect the white end of SATA power cable to the power connector of the power supply. It will allow better tolerance for memory compatibility when it is set to [Enabled].
Align the card connector with the slot and press firmly until the card is completely seated on the slot. Unplug the power cord from the 4p socket before touching any component.